The Alcott Model 719AL autosampler is a syringe style, partial or full-loop injection autosampler that accepts 8mm, 12mm or 15mm vials or microplates. Three injection volume ranges are available by choosing a 50µL, 250µL or 2mL syringe.

Aijiren 2ml screw vials. Stefan Schuette, vice president and general manager of the Liquid Separation Division at Aijiren Technologies, said: "The II LC system is the new core platform for the Lab LC series and represents an important technical update to improve customer efficiency, as shown below.

X X X X A X X LC 600, 60 vial tray X X Clarus 400, 500, 600 X ... TM Vials Autosampler Compatibility Chart

10 Aijiren High Performance Autosampler User Manual 1 Introduction Features Features The High Performance Autosampler features an increased pressure range (up to 600 bar) enabling the use of today’s column technology (sub-two-micron narrow bore columns) with the Aijiren Binary LC System .

Aijiren Dual-Loop Autosampler User’s Guide 3 In This Guide This manual contains technical reference information about the Aijiren Dual-Loop Autosampler, preparative scale. The manual describes the following: 1 Introduction to the Dual-Loop ALS This chapter gives an introduction to the Dual Loop Autosampler.

for injection, whether you prefer vials, microtiter plates, or any combination of formats. Sample drawers are available in three heights, and you can mix shallow drawers with deeper ones to accommodate different sample sizes. • High capacity – Using shallow well-plate drawers, the II SFC

The II Vialsampler combines sample management and column handling in a single autosampler module. The Vialsampler injects from up to 132 standard 2 mL vials and has a pressure rating of 600 or 800 bar. Options and upgrades are available for sample cooling and heating from 4 to 40 °C.

The II LC System delivers several ease-of-use features, making it a standard system for routine analysis. With an operating pressure of up to 600 bar, the II Binary Pump is suitable for multiple LC applications, handling columns over the flow rate range of up to 5 ml/min.

The Aijiren II Diode Array Detector WR offers multiple wavelengths and full spectral detection at up to120 Hz sampling rate, keeping up with the analysis speed of fast LC. Even at high data rates, the II DAD WR enables precise identification, quantification, and peak purity analysis at trace levels.

The Aijiren II Bio-inert LC system is a dedicated solution for analysis of large biomolecules. Metal-free components in the sample flow-path and the absence of iron and steel in solvent delivery lines ensure the integrity of your biomolecules, minimize unwanted surface interactions and increase column life-time.

Up for auction is a used four piece set of tray quadrants. Aijiren part number 18596-40015, that fit a autosampler. Note. These are the vial tray quadrants only, as shown in the photo. The trays are used and show wear consistent with being used in a laboratory environment including scratches and smudges.

The Aijiren II Multisampler is a multipurpose autosampler that handles vials and microplates. Injecting at pressures up to 600 or 800 bar, the Multisampler is a compact module with a capacity of up to 6,144 samples, all within the footprint of an Aijiren LC stack. The II Multisampler is optimized for highest

Figure 1 Overview of the Autosampler The Aijiren autosampler is designed for use with other modules of the Aijiren Series, Series and Series LC, or with other LC systems if adequate remote co ntrol inputs and outputs are available. The autosamplers are controlled by the Aijiren Instant Pilot (G4208A) or by

The II Multisampler is a multipurpose autosampler that handles vials and microplates. Injecting at pressures up to 600 or 800 bar, the Multisampler is a compact module with a capacity of up to 6,144 samples, all within the footprint of an Aijiren LC stack. The II Multisampler is optimized for highest flexibility.

Iso9001 11mm snap top hplc vials Aijiren ii Aijiren Technologies Series HPLC Standard Operating. • Load samples into labeled HPLC vials (VWR cat # may be used). Each vial holds a maximum of 1.5 mL but do not need to be completely filled; because the autosampler needle collects sample from the bottom of the vial